Todays Tools Plumb Tub

Product Information

We have all seen pictures in home improvement magazines of a beautiful, classic freestanding bath placed in the centre of a grand and spacious bathroom. Freestanding baths are the epitome of bathroom luxury. However, plumbing a freestanding bath can seem mind boggling and in some cases even deter homeowners from buying.... Then there's the volume of the fluid in the radiator itself to consider. The Plumb Tub holds just over a litre If you’re doing this yourself, you’ll need a PEX pipe cutter, crimp rings, elbow fittings, push-to-connect fittings, a crimping tool, deburring tool, go/no-go gauge, marker, and tape measurer.

The table below lists each DWV fitting used to plumb this simple bathroom. Notice each plumbing code has its own column with the specific quantity of needed fittings. The most popular material for water lines these days is PEX (short for cross-linked polyethylene). PEX is flexible, and much easier to work with than copper, steel, or PVC. These are just some essential tools to start your bathroom do-it-yourself plumbing project. Step 2: Prepare the Space Single-ended baths tend to be the most popular choice as they will fit in with almost any bathroom. Both taps are situated at one end of the bath, usually above the waste area. This style of bath is typically designed for one person to relax in the tub. The taps being located at one end is ideal for bath showers which have a mixer shower valve, as this can be fitted to the wall directly above the taps and waste. A vertical pipe should also be installed between floors with proper ventilation for air circulation.Now, the process of bathtub removal starts. Place a piece of cardboard or thin plywood in front of the tub to protect the floor from damage. Use a pry bar, screwdriver, or a drill and screwdriver bit to remove the nails or screws that secure the tub flange to the wall studs. Slide the tub several inches from the wall and onto the floor protection. Use the tub drain tool, adjustable wrench, and plumber’s putty to install the main tub drain parts. Using a screwdriver, install the overflow faceplate and pipe. Attach the two drain pipes with a drain tee, but don’t install the P trap tube yet—one of the many helpful plumbing terms to know if you don’t already. Install the hot and cold water lines for all of your fixtures. This is one of the most important parts since all of your bathroom fixtures need a water source. Most bathrooms require 5 water lines: a hot and cold line for both the bathtub/shower and the sink, and a cold water line for the toilet. Each fixture and house are different, so hire a pipefitter or plumber to run the lines for you if possible. [11] X Research source This step isn’t always necessary, but if you’re installing a new bathtub faucet or it’s low enough that it will be in the way during removal and installation, you can go ahead and remove the faucet. To remove the bathtub faucet handles, remove the handle covers with a flathead screwdriver and then unscrew the screws that hold the handles in place. Gently pull them from the wall and off of the pipe. If the handles are difficult to remove, you may need a handle puller for this step. If you cannot locate a shut-off valve for a specific fixture or need to turn off the water supply to the entire bathroom, you can turn off the main water valve for your home. This valve is typically located near the water meter and may require a unique tool to turn off. Remove Fixtures and Accessories

Your job isn’t done when you’ve bought the bath; you also need to think about the things that go with it. Inset baths, for example, will need a bath panel for the final touch, unless you want the underneath of the bath on show. There’s a range of styles and finishes available, but you obviously need to make sure it matches both the bath and the rest of your bathroom. If you are installing a new plumbing vent, be sure to slope it correctly during the installation process. If you notice an existing vent that is not sloped, it is recommended to call a licensed plumber to assess the issue and make any necessary repairs or adjustments. Final ThoughtsReplacing your bathtub is a big project that can beautify your bathroom and make bath time inviting again. You can employ your intermediate DIY skills with patience and a helper to accomplish the job over a weekend. If you’re up to the challenge of learning how to install a bathtub, removing and replacing your tub can save you money over a complete bathroom remodel, and you’ll save big by providing the labor yourself. Prepping to Replace Your Bathtub

Steel baths are the strongest type of bath. They are strong, durable and can last a lifetime when looked after properly. While they are extra sturdy, they are also cold to the touch, which means it can take more effort to keep bath water warm. Here are some steps to follow when preparing your space for a plumbing project: Turn off the Water Supply Before starting any plumbing work, you’ll need to turn off the water supply to the bathroom. This can typically be done by turning off the main water valve in your home or apartment.

The key to success when installing a new bathtub is to make sure the new one fits perfectly in the void left by removing the old tub. Most alcove-style bathtubs measure 5 feet long and between 28 and 34 inches deep. It’s challenging to get an exact measurement from the existing tub while it’s still in place. Fortunately, bathtubs come in standard sizes, so your educated guess from the tape measure will be the correct measurement. Cut a two-by-four board to match the length of the bathtub. Line up the two-by-four’s top edge with the lower marks on the stud and attach it with exterior grade screws to each stud. The product is created in an adequately soft yet sturdy plastic, with decent 'clips' surrounding the 3 holes which will fit round the various diameter pipes of your heating system. The two major plumbing codes in the United States is the IPC (International Plumbing Code) and the UPC (Uniform Plumbing Code). Each connection must be secure and leak-free when connecting the water supply lines to valves and fixtures. The central drain line should be connected first, followed by the toilet drain or shower drain. Toilet flanges should be installed on existing drain lines before connecting them to the main sewage line.