COMFAST WiFi Booster WiFi Repeater (300Mbps, White)

Product Information

Make sure you set up the WiFi access point inside first and confirm it is working, and only mount it in the intended position when you have verified that it provides a connection to the internet. There’s no point in wasting your time installing a wifi extender if your router is in poor working condition. A good wifi router will operate nicely for a few years, but if you have had the same router for four or five years, it’s probably time to get a new one. Even if it seems to be working well, a new router will give off a better signal. Some of the more expensive range extenders - such as Netgear’s new EAX80 model - can eliminate this problem by merging their own Wi-Fi network with the network from your main router. In this article we will take you through how to configure your Comfast Wireless Bridge which can help you guarantee a reliable connection for a wireless CCTV system. Yes, you will need to reconfigure your extender if you replace your existing router/gateway. You can reconfigure your extender either via WPS connection or using the web GUI.

Solution home Green Feathers Outdoor Long Range Wireless 2GHz WiFi Access Point (COM2G) Setting up a Comfast long range WiFi access point Desktop and Notebook PCs, Wired and Wireless Routers, Modems, Printers, Scanners, Fax Machines, USB devices and Sound Cards If this has not already been pre-configured for you by our Helpdesk team, you will need to log in to the access point and set it up, see below for how to do this.Fury vs Ngannou live stream: how to watch boxing online now, PPV prices, full fight card, start time, odds This is called ‘roaming’ as it allows you to automatically switch between the router and the range extender, depending on which one is closer and provides the strongest Wi-Fi signal. Plug the extender into the wall, then plug the Ethernet cable into both the extender and your computer. Alternately, disconnect from your home Wi-Fi network and connect directly to the extender. Note that in both cases you’ll temporarily lose web connection. If there’s a switch on the side of your extender, make sure it’s set to “Extender” mode, not “AP” or “Access Point.” (AP is for connecting directly to your modem, which you don’t need if you have a Wi-Fi router already, or an all-in-one modem/router.) It may need a few minutes to boot up.

Once your device was properly connected. The Comfast Wi-Fi repeater hitch attachment is known as Home Network PLUS. Without WPS it may take a little longer to connect your wifi extender, but the idea is the same. First, you’ll want to connect the end of your Ethernet cable, or Cat5 cable, into the Internet port on the extender and the other end into the Internet port on your wifi router. Note: If your extender supports AP mode, you will be prompted to select how you would like to setup your extender. Select the “ Wi-Fi Range Extender” button. If you will be connecting a WiFi camera or something similar, it is also best to connect it whilst quite close to the access point, then mount the camera in the final position once it has already been connected to the access point. Every brand of network hardware is a little different, and we can’t cover them all. Generally if you follow the instructions that came with your extender, you should be okay. That being said, there are usually two different ways to go about it:

This WiFi access point sends a 2.4GHz WiFi signal, which allows WiFi cameras to easily connect to it, as well as any other WiFi devices that have compatibility issues with 5GHz devices. If the link LED is OFF, the extender failed to connect to the router Wi-Fi network, please repeat steps 1-3 to try again. That’s a bit confusing, but the app does allow you to change the name of the range extender network to something that’s easier to remember. Let’s keep it simple by calling it 'Range Extender 2.4GHz' and 'Range Extender 5.0GHz'. To reset the Comfast extender, press and hold the reset button for 10 seconds with a paper clip or similar instrument. Slide the port cover off the bottom end of the WiFi access point, then connect one end of the long ethernet lead to the port on the POE injector marked 'POE' and connect that to the port marked 'WAN' on the WiFi access point.