Visual Fault Locator (VFL), Red Light Pen 10mW Fiber Optic Cable Tester Meter with 2.5mm Connector for Fiber Fault Finding, Up to 10KM

Product Information

Visual fault locator cable continuity tester locates fibers, finds faults, verifies continuity and polarity. Step 2: Connect the fiber visual fault locator to the opti-crimp connector ferrule (with the included patch cord), turn on the VFL. Networks Centre presents the Fluke Networks Visual Fault Locator as part of our Cable Testing and Measurement range.

Visual Fault Locator Tutorial | FS Community Visual Fault Locator Tutorial | FS Community

See connectors that have damaged fibers inside. A damaged fiber inside a connector causes a red light in the connector. All visual fault locators can work with both single mode and multimode fibers. Since multimode fiber has a 50um or 62.5um core, which is much bigger than single mode fiber's 9um core, more light power can be coupled in to multimode fibers. That translates to longer fiber distance for multimode fibers than single mode fibers. Modulation frequency (CW and 2Hz)The VFL enables the operator to view the optical fiber break. The optical fiber may break in places other than fiber optic cables. Inside the connector or connector ferrule, the optical fiber may break. A microscope cannot see the optical fiber unless it is damaged at the end face of the connection. Visual Fault Locator which can be also called visual fault identifier (VFI), fiber fault locator, fiber fault detector, etc, is a visible laser available in red laser light and designed to inject visible light energy into an optical fiber. It is a cost-effective way to spot defects of fiber glass such as sharp bends, breaks, faulty connectors and other faults which will "leak" red or green light visually. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. No matter for installing new fibers or troubleshooting the existing networks, visual fault identifier is a helpful handy kit. The laser-powered VisiFault locates fibres, verifies continuity and polarity, and helps find breaks in cables, connectors and splices. Step 1: Clean the fiber optic cable connector endface and attach your visual fault locator to the connector.

Visual Fault Locators | VIAVI FFL-050/-055/-100/-105 Visual Fault Locators | VIAVI FFL-050/-055/-100/-105

Clean ST connector ferrule end face with a lint-free wipe (FWP-C) soaked with alcohol (reagent grade isopropyl alcohol, with a minimum 90% concentration). A visual fault identifier or visual fault locator (VFI / VFL) is a visible red laser designed to inject visible light energy into a fiber. Sharp bends, breaks, faulty connectors and other faults will “leak” red light allowing technicians to visually spot the defects. Continuous and flashing modes make for easier identification. Compatible with 2.5mm and 1.25mm connectors for easy connection. Ruggedly constructed for demanding field-testing. In the same way, the visual fault locator can be used to assess the continuity of an optical cable. When utilizing a continuity tester, the first step is to clean and visually verify the connector’s end face before inserting it into the continuity tester. After cleaning and inspecting the connector, make sure the continuity tester is working properly. Turn on the continuity tester and make sure it is emitting light. How to Use To see the light that comes out of a connector, hold a white paper in front of the fiber connector.Taking FS Pen-Type Visual Fault Locator, 1mW as example, it is small in size and easy to be carried away. See high-loss bends. If you can see the light from the VFL at a bend in a fiber, the bend is too sharp. The Visual Fault Locator is available in different shapes and sizes. Some may look like a pen, others may be built into an optical time domain reflectometer (OTDR), and some may look like a small test equipment box. Pen-Type Visual Fault Locator Once there is a fault, light will leak out from the cladding and the light will not go through the other end of the cable. The Visual Fault Locator (VFL), like the continuity tester, is an essential instrument in any fiber optic tool kit. The VFL is not one of the cheapest instruments in your toolbox. Function

Visual Fault Locator | Fibre Optic - Networks Centre - NetworkCentre Visual Fault Locator | Fibre Optic - Networks Centre -

It will help you to easily discover optical fiber breakage or macro bends, as well as a bad fusion splice in multimode or single-mode optical fiber.

Increase the quality of mechanical splices and prepolished connectors: Before you seal the splice or connector, adjust the fiber alignment for the minimum amount of light where the fibers touch. (Refer to the instructions from the manufacturer when you make splices and connectors.) Typically, the light emitted by the optical fiber will illuminate the buffer that surrounds the optical fiber. You can diagnose and repair simple fiber link problems with Fluke Networks' VisiFault TM Visual Fault Locator (VFL). The laser-powered VisiFault Visual Fault Locator is a cable continuity tester that locates fibers, verifies cable continuity and polarity. This cable continuity tester helps find breaks in cables, connectors and splices. Continuous and flashing modes make for easier identification. Compatible with 2.5mm and 1.25mm connectors for easy connection. Ruggedly constructed for demanding field-testing. This visual fault locator has a long battery life for hours of use. Clean and inspect the fiber optic cable connector with a microscope. If the endface finish is acceptable, the VFL can be connected to a fiber connector.

VFL - Visual Fault Locator | Fluke Networks VFL - Visual Fault Locator | Fluke Networks

If the end face finish is acceptable, the VFL can be attached to a fiber connector. During this testing, the VFL should not be viewed directly. The VFL directs laser light into the core of the optical fiber. The laser’s light exits the optical fiber at a break or macro bend. Clean the split sleeve with an alcohol soaked cleaning swab (FSWB-C). Replace the split sleeve onto fiber ferrule and screw housing into place securely. You can diagnose fiber link problems over fiber optic cables or fiber cable pigtails using visual fault locators. When the fiber fault locator is designed with adapter incompatible with your connector type, using additional adapters is necessary. The fiber distance spec tells the longest fiber length where you can still see the leakage light without difficulty. This spec is determined by the laser light power. The industry standard spec is 10km for multimode fibers and 5km for single mode fibers. FS high power 30mW fiber optic fault locator enables up to 15km dynamic distance. Output powerUse the VFL button to turn on the visual fault locator (see picture below). Or, on the home screen tap TOOLS, then tap Visual Fault Locator (VFL). You can tap the PULSE/OFF/CW (continuous wave) button on the screen to change the modes of the VFL, or use the button as shown in the picture below. Output power is an important spec for visual fault identifiers. Some may ask how many power do I need? The key is: The higher output power is, the longer fiber distance it can support. This spec is usually 0.5mW coupled to single mode fibers and 2mW to free space (which means no fiber coupling, just the light output from the tester's connector adapter). Fiber mode