Ronseal Diamond Hard Floor Varnish Clear Matt 2.5L

Product Information

Gradual Hardening: These are varnishes where there is a ongoing reaction between the oils and resins after the solvent has evaporated, which make continue for several days in some cases, before the varnish is hard and fully cured. In this case the exposure to the air causes oxidation and polymerization which may occur over a series of processes and take a few days A matte finish is a trendy choice right now. However, it is considered a flat finish because of its 25% luster. Using a soft cotton cloth, apply a tiny amount of tung oil, boiled linseed oil, or teak oil. Working with the wood’s grain, rub the oil into the finish, continue rubbing until there is only a tiny amount of oil left on the wood. Alkyd Varnishes – This is a terms that you will sometimes hear, and most varnishes will contain an alkyd of some kind. They are modified natural or vegetable oils.

For the best protection on flooring, we recommend applying 1 coat of Manns Extra Tough Primer followed by 2 coats of Manns Extra Tough Floor Varnish, using your chosen application methodHowever, you can reduce the sheen of an oil-based finish by using hand rubbing with polish or wipe-on varnish. Here’s the step by step process of how to make matte finish on wood; Apply A Non-Shine Polyurethane Finish. You will always apply the stain before applying the varnish, unless the varnish already has the stain mixed into it. Allow sufficient time for the solvent to fully evaporate before applying the finishing coat of say, varnish. If it is wet or cold we suggest that you leave another 24 hours over the manufacturers’ recommended drying time to be 100% safe. Using 400-grit or finer wet/dry sandpaper, scuff the finish. Moisten the paper with a small volume of water to help it smoothly cut the finish more.

Unlike paint, varnishes and stains are designed to soak into the wood. You can even apply a clear varnish to the stain to improve the finish and also make it more durable. These are also available in solvent and water based variations and also in a variety of colours and shades. Floor to be varnished should first be primed with one of the following Manns wood primers. Primers aid with adhesion between the floor and the varnish and can offer a cost saving when varnishing large areas. Product Much like paint, varnishes have finishes that vary from “Gloss” through “Satin” to “Matt”. This describes the sheen of the finish and how reflective it will be. Gloss is the shiniest and smoothest, while Matt describes a dull and un-shiny finish. Choosing the Right Varnish Apply the first polyurethane coat gloss (water- or oil-based), allow it to dry, then use sandpaper to scuff it off, either wet or dry.Varnish can be applied with a brush, which is more typical, or a roller. If you are planning to use a roller use one with a short pile. See here for help on choosing a roller. Apply with the grain to get a smooth and even finish. Pigment: This is the part that provides the colour. Some people differentiate between pigments which are held in suspension and dyes which are dissolved in the ‘vehicle’ or solvent. Essentially it makes little difference to the user, except that pigments held in suspension will be large molecules and will not penetrate the structure of the wood as much which will make them more opaque. The colours are generally browns and wood effects, but you can get highly colourful stains which will colour wood in all manner of colours There is a huge range of different varnishes out there and different manufactures will call them slightly different things to make it even more confusing. Gives floors Diamond Hard protection from shoes, scratches and spills, while highlighting the natural beauty of the wood.

Make sure that the stain is thoroughly mixed before you start to apply it so that you get an even colour throughout. Applying a Stain

Wood Stains and Using Stains

Hopefully with a good understanding of what the various elements do, you will understand how the various characteristics that the manufacturers’ have developed in their varnishes can be best used. Wood Stains and Using Stains To reduce bumps and defects in the finish, stroke with the grain with moderate pressure. To rub the wax or polish off, use a clean cloth or an electric buffer that has a lambswool buffing cloth. Why Matte Wood Floor Finish? Appealing To The Eye It’s the finest for masking wood flaws, and it’s suitable for houses with kids, dogs, and a lot of foot activity. Its low-gloss coating effectively hides regular wear and tear. Sand down lightly after the first application and if necessary apply another coat. This will make the colour bolder and darker. We would strongly recommend practicing on an off cut to get the measure of the stain before you start on the real thing, especially if you’re not familiar with using stains. Even if you are, it is important to see how the stain will work with your particular wood you are using. Next, smear a second coat if necessary. Depending on the quality of finish you want, you can either rub out this coat or scuff it and apply the third layer.