Knightsbridge SN8300 Standard Pull Cord Switch 2 Way 10A, 230 V, White-2W

Product Information

Step 1 – Firstly isolate the power to the circuit you are working on in your consumer unit by turning off the MCB for that circuit or if a fuse box, pulling out the fuse. If you are unsure which is which, turn off all the power using the main isolator switch Before you disconnect any wires always test the wires and make sure that they are not live – you don’t know who installed it and if it’s installed properly so it’s better to be safe than sorry. Pull the switch free and turn it over to access the wires. Take a picture of the wires (normally just 2), noting exactly which wire is in which terminal. Again, if this has does not work, the whole unit must be replaced. Replacing the Cord From a Pull Cord Switch If you want to try and save your broken switch, rather than throw it away and replace it with a new one, work through the steps below for your chosen type of switch. Repairing a 6amp Pull Cord Light Switch

In this DIY guide we look at how to install a pull cord switch. Regulations for Installing Pull Cord Switches

How to Replace a Pull Cord Switch

Form a knot and then lower the finial to cover it. Other types of finial are available, such as timber or porcelain/ceramic, from hardware or DIY stores.

If this is ignored then you may face problems when trying to sell your property as if its had notifiable electrical work carried out, but for which the appropriate certificate from a qualified electrician cannot be produced. Additionally, it will also propably invalidate your home insurance. The neutral wire should also have a brown sheath or brown tape wrapped around it to indicate that it’s the switched live, but this will depend on the wiring setup. As long as you wire it up the same as the old switch, all will be well. Pull switch alarms often have a red cord or handle to draw attention. They are used in disabled toilets, for example, if someone needs to raise the alarm for assistance. Therefore pull switch alarms need to stand out in case of emergency. 1-Way vs. 2-Way Pull Cord Switches

Types of Pull Switch

A pull cord switch, sometimes called a light pull, is an electrical switch which features a cord or string to control it. These switches are commonly found on the ceiling of bathrooms or other areas where water is present. Why use a pull cord switch? Step 2 – Undo the two retaining screws holding the switch in place and carefully pull it down a little. There should be sufficient wiring to allow you to do this as with the lighter duty switch above Step 3 – Spray the switch area with the a little maintenance spray or WD40 and attempt to loosen the spring to make the switch work properly. Hold it with one hand and pull the cord with the other To do this, turn off the MCB of the lighting circuit you’re working on or if a fuse board, pull out the fuse.

To fit a pull cord switch or indeed just replace the cord, you will need the following tools and products. Pull cord switches are very handy items as they can be used in a variety of situations such as bathrooms and the similar where a standard tumble-type switch cannot be used. Use a small flathead screwdriver to undo tightening screws and pull the wires out. Then unscrew the base unit which is mounted to the ceiling and remove the old unit. Now you are ready to install your new pull cord switch. For the first part of this guide we will work through replacing a standard 6 amp pull cord light switch. From step 6 we will explain changing a 45 amp isolation switch. Step 1 – Isolate the Switch and Circuit One thing to note however is that the switches do differ slightly. Whereas the 6 amp switch is single pole, the 45 amp switch will be double pole as it needs to be able to isolate both the live and neutral.

The very first job to do before anything is to ensure the electricity is isolated for the circuit you will be working on. Step 3 – Using some maintenance spray such as WD40, apply the lubricant to the inside of the switch, where the wires are connected, especially in around the pull cord section If you just want to replace your broken pull cord switch then work through the steps below. However, if you want to have a go at repairing your existing switch then scroll down to the sections we have on repair. Standard 6amp pull cord switch Tools and Materials Needed for Repairing and Replacing a Pull Cord Switch