StarTech 3 feet Shielded External eSATA Cable M/M, Black

Product Information

USB 3.0 is another generation of USB. In computers where all the devices and drivers are compatible with USB 3.0 peak performance, it provides significantly better performance than USB 2.0. An ATA hard drive will also have different jumper settings depending on whether it is connected as slave or master. Note: Confirm that your BIOS is NOT set to SATA legacy mode. eSATA is disabled as default with this setting.

The final eSATA specification features a specific connector designed for rough handling, similar to the regular SATA connector, but with reinforcements in both the male and female sides, inspired by the USB connector. eSATA resists inadvertent unplugging, and can withstand yanking or wiggling which would break a male SATA connector (the hard-drive or host adapter, usually fitted inside the computer). With an eSATA connector, considerably more force is needed to damage the connector, and if it does break it is likely to be the female side, on the cable itself, which is relatively easy to replace. If advanced functionality such as a port multiplier is required, a PCI Express add-on card can be used. If it has port multiplier support, an eSATAp port allows a user to connect to a multi-bay NAS ( network attached storage) machine with multiple hard disks (HDD) using one eSATA cable. Connect one end of the SATA cable to the hard drive, then connect the other end of the cable to one of the free SATA connectors on your motherboard. Press the key once every three seconds while the initial Dell logo is on the screen to enter the BIOS.

About The Author

Serial Advanced Technology Attachment cables are special types of cables, which are mainly used to connect multiple types of storage drives (optical drives, hard drives, solid-state drives) to a motherboard. The new SATA interface combined the SATA and the PCI Express buses. Legacy SATA and PCI express storage devices could now co-exist eSATAp PCI and PCI-e add-on cards are available for desktop computers. They usually provide two eSATAp ports, with port multiplier functionality, and hot-swap capability. If the smaller side of this cable is plugged into a "powered" ESATA port, providing both 12 V and 5 V, then the wide end may be plugged into a 2.5" or 3.5" SATA hard drive, supplying the bare drive with both signal and power. The small 2.5" drive will get signal and power at 5 V, which is all that the smaller drive requires, and which the larger 3.5" drive requires only for its logic board. Additionally, the larger 3.5" drive will get the 12 V it needs to power its disk spindle motor. Thus a bare hard drive may be attached directly to the computer, powered by the unique cable, where it will run at full SATA speeds, without the necessity of placing the hard drive into an external enclosure.

The SFF-8639 connector was renamed to a more consumer friendly U.2. This connector is used with some new NVMe SSDs. U.2 utilizes 4 PCIe 3.0 lanes to provide speeds much faster than the SATA interface. Since most motherboards do not have a U.2 connector on them, a M.2 to U.2, or PCIe to U.2 adapter can be used. Note: For more informationabout entering the BIOS, the BIOS configuration, orrestoring the system setup defaults, refer to the Online User's Guide . FireWire comes in two speeds - FireWire 400 and FireWire 800. FireWire 400 (also known as 1394a) usually gives performance similar to USB 2.0. FireWire 800 (1394b) is significantly faster, giving performance similar to an internal Serial ATA drive, and is almost exclusively available in Mac computers. Also see: Look! Everything You Need to Know About eSATA External Hard Drive SATA Cable VS PATA Cable This article needs to be updated. Please help update this article to reflect recent events or newly available information. ( October 2023)There can be two or four ATA ports on any one motherboard. One cable can connect to two devices at the same time. With an eSATA drive attached, AHCI mode enabled, and eSATA disabled in BIOS, eSATA must be enabled in theBIOS. This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. ( October 2011) ( Learn how and when to remove this template message) Most USB cables that come with Seagate and Maxtor-brand drives look like this. Note that the connection size for the connector on the drive is smaller than, for example, a USB port on a printer, but many digital cameras use the same size connection.

Although there are usually only 2 PATA connections on the computer motherboard, there will usually be 4 to 6 SATA connections, which allows multiple SATA hard drives to be connected at once. Cable Management ATA is a very common connection for internal drives in older PCs and older desktop Macs (before G5), and for devices like CD and DVD drives in modern PCs and Macs. It is a connector about 2 inches (5 cm) wide and has 40 small gold pins that will fit into the corresponding 40 small holes on its corresponding connector. Note: eSATA uses the same technology as that used in the internal Hard Disk Drive (Hard Drive) units of your computer. This saves having to translate data between the interface and the computer. Cables are serial and can be up to 6 and a half feet to 2 meters in length. Unless you are using one of the eSATAp ports, you require an external power source for the storage device. Regular eSATA ports do not supply power. SATA 3 interface is quite fast and has super transfer speeds. Can you use a SATA cable on a computer that doesn’t have a SATA connection port?See here a close-up illustration of the adapter fitting into its power connector on the SATA drive.