Ubiquiti US-16-150W 150 W 16 Port UniFi PoE Switch

Product Information

EdgeMAX products are managed with a per-device web interface, or via SSH. These web interfaces are not as polished or pretty as UniFi, but they expose more advanced features than UniFi does. EdgeSwitches also have the full EdgeOS CLI for configuration. If you’re familiar with JunOS or IOS, you’ll be able to figure out your way around. See Ubiquiti’s CLI Command Reference user guide for more details. Putting the L2/L3 differences aside, the 2nd generation pro models also have some other advantages over the non-pro UniFi switches. 2nd Gen Pro models add

If you want 10 Gbps ports for clients, or need a distribution switch to aggregate other switches, the XG series has a few options. Some are in the 1st generation, some are in the 2nd: EdgeSwitches are older, more traditional managed switches, with command line (CLI) and individual web interfaces for configuration. EdgeSwitches also have optional integration with the UISP software controller. The newer UISP-branded switches are tied closely to the UISP software, have no web interface, but still offer a CLI for manual configuration. I cover EdgeSwitch and UISP hardware briefly below, but I cover them in more detail in my UISP Switch review. Wait for the device to fully boot, the led will turn dark blue (or stay white if it wasn’t adopted before, approximately 5 minutes max) This Ubiquiti US-16-150W UniFi switch offers sixteen (16) PoE Gigabit Ethernet ports of auto-sensing IEEE 802.3af/at or configurable 24V passive PoE to simplify your infrastructure. By default, the Ubiquiti US-16-150W UniFi switch automatically detects 802.3af/at devices so they automatically receive PoE. For 24V passive PoE devices, manually enable 24V passive PoE using the UniFi Controller software. Fiber ConnectivityBasic layer 3 features like static routing (supported as of firmware version 4.3.13.11253) and inter-VLAN routing. A common complaint with the first generation models are their loud fans. It is possible to replace them with quieter Noctua fans, or you can throw it in a network closet and forget about it. If you just need basic L2 switching and PoE, the first generation models are still worth considering, especially if budget and availability are more important than future software support. Its enterprise level equipment, so you pay a little more than consumer, but it is in reach of a homeowners budget. I highly recommend it. Read full review To cache the firmware in your controller you open your controller and go to the settings (lower left gear icon). Search for Firmware and select Device Firmware Cache (or select Updates > Firmware in the settings menu)

Do not have a serial console port. All management has to be done over Ethernet in-band. (EdgeSwitches still have console ports!) Have a small touchscreen on the left side of the device, like the UDM-Pro. This screen shows stats and info about the device, and the network it is on. They also integrate with the UniFi AR feature, which lets you use a phone to virtually see what is connected to each port. When the reboot is completed the led will turn pale blue. You can now adopt the switch in the controllerHave lower fan noise — the non-pro models are fanless. The pros have fans, but are quieter than the 1st generation models. The USW-Flex-XG is a 2nd gen model, with one 1 Gbps and four 1/2.5/5/10 Gbps RJ45 Ethernet ports. No PoE.

It’s also worth pointing out that PoE devices don’t always consume their maximum rated power draw. The spec sheet will specify the maximum amount the device can use, but during normal operation they won’t use that much. For example, the U6-Pro requires 802.at PoE+ or 48V passive, and maxes out at 13W. During normal use it usually consumes around 5 to 7 watts of power. If you are planning on using PoE passthrough on switches like the USW-Flex, or access points like the In-Wall-HD, you should supply them with the higher-wattage PoE+ or PoE++. Devices with PoE passthrough will usually function when fed with standard 15W PoE, but will not reliably power downstream devices unless they receive their maximum rated power input. For example, the USW-Flex can provide 8W with PoE in, 20W with PoE+ in, and 46W with PoE++ in. PoE passthrough is when a PoE device can receive power and also pass PoE to another downstream device. A common example would be a 24 port PoE switch, feeding an In-Wall-HD access point, with a video camera connected to the In-Wall-HD. The key part is that all three devices are drawing their power from the 24-port PoE switch. In situations like that, you need to be especially careful about what PoE support your switch or voltage and amperage of your PoE injector.Ubiquiti calls them “Gen2” but I am going to call them 2nd generation. Whatever you call them, Ubiquiti’s newer UniFi switches split things into a few tiers. There are models which replace the 1st generation switches, and the higher pro and enterprise tiers.

I’ll use the PoE, PoE+, PoE++ names as shorthand. It is important to consider the type of PoE you need for your devices, and to make sure that you have enough PoE budget on your switch to power all your devices. Otherwise, you will need to rely on separate power injectors. PoE Passthrough Deciding between UniFi, EdgeMAX, UISP, or some other brand depends on your needs. The right solution varies with what kind of network you are trying to build, and what features you need to accomplish that. If you are comfortable with command line configuration and have complex needs, another vendor is probably a better option. This guide focuses on UniFi switches, but it’s worth noting some EdgeSwitch models are the same hardware as the first generation UniFi switches, with an EdgeOS CLI and UISP instead of the UniFi controller. The newer UISP switches are not as mature, but are worth considering if you want your switch to tie into the UISP NMS and UCRM software. I adopted it and upgraded the firmware. It took longer to unbox and mount it than it did to set it up. Higher PoE budgets. The 2nd generation non-pro models are fanless and have very limited PoE budgetsI mounted it, plugged it in to power and the other switch I had. By the time I got upstairs, the controller already found the new switch. Passive 24V and 48V PoE — Ubiquiti’s standard, mostly used on EdgeMAX, AirMAX, and older UniFi devices Also worth noting — if serial console out-of-band management port is something you need, the first generation switches have it, and the second generation models do not. XG UniFi Switches USW-Flex — When using PoE passthrough ( Note: this was upgraded to 802.3at PoE+ in a firmware update)