Rustins Polyurethane Varnish Clear Matt 1l

Product Information

Now that you know how matte and satin polyurethane compare, it’s time to decide which is best for your project.

The instructions on all polyurethane cans say to stir well before use. That’s because the zinc oxide sinks to the bottom of the can as it sits on the shelf. Stirring ensures a uniform result by distributing the paste evenly throughout the product. The expert at Minwax said, “the main difference is the appearance. Satin reflects more light and is shinier than matte.” He also confirmed that ” you’ll see more dust and scratches with a satin polyurethane because it’s shinier. It doesn’t get dirtier than matte, but it appears dirtier.” Another factor to consider, especially if you’re finishing a floor, is how the appearance of the finish will change over time. What’s the difference between matte and satin polyurethane? What factors should be considered before choosing? Are you planning to refinish wood floors, cabinets, or furniture but can’t decide whether to use matte or satin polyurethane?He said, “higher sheens show debris and wear more than lower sheens, but the difference between matte and satin is small. You’ll notice a much bigger difference if you compare matte and semi-gloss.” Since the main formula for matte and satin polyurethane is the same, both provide the same durability and protection. Remember, the only difference is the amount of zinc oxide paste, which determines the sheen level but doesn’t impact durability. On average, you’ll need to refinish floors every ten years. Of course, it also depends on how much wear they experience or if they receive direct sunlight. If you see gouges or scratches, discoloration, or decreased luster, it might be time to refinish your floors. What Experts Say About Matte vs. Satin Polyurethane Regardless of the finish, cleaning and maintaining floors coated with polyurethane is simple and easy. Frequency of cleaning: Consider how often you want to clean. Remember, satin will need to be cleaned more frequently. Matte is a bit more forgiving.

Bottom Line — the best polyurethane finish is one that will reflect your needs, lifestyle, and preferences. If you’re going for a low-maintenance, rustic look without sheen, choose matte. If you want a subtle shine and don’t mind dusting and cleaning more often, go with satin. As with all wood varnishes, ensure that the substrate that is to be varnished is sound and free from any surface contaminant likely to cause adhesion problems – e.g. wax, grease, polish, etc. Always degrease previously wax polished floors prior to sanding and applying the polyurethane varnish.Wear-and-tear: For high-traffic areas, consider an oil-based polyurethane. It stands up well to wear-and-tear, but it has a more pungent odor for seven to ten days after you apply it. Choose a satin finish to give it a touch of sheen for a richer look. Level of sheen: Consider testing each finish on a small piece of wood or furniture. Light reflects off surfaces differently in each room. Seeing the finish in the room will help you decide. Although labelled as a clear polyurethane varnish, as with any varnish, the finished effect depends on the type of wood it is applied to – with some darkening the wood grain. Semi-Gloss is a step up in sheen from satin. It’s not overly shiny, and hides wear better than high-gloss. It’s a good choice for people who want some shine but not too much. It brings out the beauty of the wood.

Wood and water don’t mix. So, never soak or oversaturate wood when mopping. Water can penetrate the polyurethane and seep between the floorboards, leading to cupping, warping, and other irreversible damage to the wood. To get an expert opinion on matte vs. satin polyurethane, I reached out to the two most popular manufacturers in the industry: Minwax and Varathane.

Pallet agreements which are about to expire

High-Gloss offers the highest shine. However, it shows all imperfections. It is best suited for specialty floors with low traffic or any wood you want to showcase. Durability and Maintenance In terms of appearance, all polyurethane starts out as a high-gloss finish. Zinc oxide paste is added in different amounts to flatten the shine. The key difference between matte and satin polyurethane is the appearance. Matte reflects almost no light, giving it a dull, low-sheen look. Matte’s gloss level is between 15-30%. Satin is also a low-sheen finish, but it reflects more light, making it slightly shinier. Its gloss level is between 30-40%. Application: Brush only. For Health and Safety reason related to all solvent-based paints, spray application is not recommended. STIR THOROUGHLY BEFORE USE. Product is ready to use. Do not thin. Apply up to 3 coats of Dulux Trade Polyurethane Varnish. Dulux Trade Polyurethane Varnish is not suitable for use on other surfaces such as masonry. On surfaces subject to heavy wear such as flooring, the gloss finish is recommended. Application equipment for water based polyurethane varnishes can be cleaned-up with soap and water – always refer to product datasheets for manufacturer specific recommendations for cleaning and storage.

With a satin finish, you’ll get the beauty of a subtle luster. But you’ll need to clean it more frequently than matte to keep it looking good. Polyurethane varnishes are super-tough ‘coatings’ popularly used as a finishing layer for protecting interior and exterior wooden floors, stairs and other surfaces prone to pedestrian wear and tear – some products can also be used on chipboard, plywood, hardboard, and parquet surfaces. Easy to use, with water-based polyurethane varnishes containing lower VOCs than solvent or oil based versions, and more durable than standard wood varnishes, they are a popular choice for woodworkers, furniture makers and restorers, and joiners. From floors to cabinets, and stairs to bar surfaces, polyurethane varnishes can deliver excellent protective qualities in gloss, matt or satin finishes. He mentioned, “most Minwax poly finishes come in satin, but only one water-based finish comes in matte. The oil-based satin polyurethanes have a slight yellow tone that enriches the word, whereas the water-based matte product goes on completely clear and doesn’t alter the wood’s appearance.” Water or oil-based: Oil-based finishes have a more pungent odor and an amber tint. They can change the look of your wood. If you prefer a clear coat, go with a water-based polyurethane formula. Many thanks for taking the time to read our blog and for you question, and thank you for your patience. For this application we would recommend Rust-Oleum 4900 Polycoat 2K, however, we would only recommend applying this this on painted or stained wood – so we would recommend this is carried our prior to the application of 4900.

Buy Online

Contain a water or solvent-based plastic resin, compared to standard varnishes containing resins, oils and solvents Today, water-based polyurethane varnishes differ from older production of varnishes, in that they produce lower VOCs than resins, oils and solvents previously used. Many manufacturers produce clear polyurethane varnishes, but they are also available in the following tints and shades: I go into detail in this guide to deep cleaning wood floors, but the basic steps are to vacuum or wipe loose dust and debris, then mop with a microfiber floor mop and fast-evaporating floor cleaner (like Bona). Suitable for all types of interior woods, the matt finish option is not suitable for use on floors, nor should it be used over French polished surfaces. Solvent and oil-based polyurethane varnishes can dry to leave a slightly amber finish, warming up the wood and its grain. Being slower to dry than the water-based products, it of course means that there needs to be longer periods of time left between additional coats.