Optical Audio Adaptor

Product Information

If better to use the receiver; I have an optical cable already. I take it from your opinion that there shouldn't really be anything in it between that and a similar quality coaxial cable? (makes sense to me). Let's look at three common situations where it is beneficial to use TOSLINK over HDMI. Keeping Older Audio Gear In Service

If better to use the panasonic dac, then should I go ordinary analogue interconnects, or the balanced pin cables? why? Even fiber HDMI cables typically have 2 to 4 copper wires, which is why they are still shielded. Pretty sure toslink is no metal outside the connections, which are often plastic also. Noise is hard to pin down sometimes because it depends on your house/apartment wiring, potential ground loops, ECT... Might be I'm overthinking it all at the 'level' of equipment i have...so if you say 'just run what you have' I get it too... :) You'll find HDMI inputs and outputs a firm fixture on the best TVs, Blu-ray players, AV receivers and, increasingly, soundbars. An entry-level cable like the AudioQuest Pearl HDMI will suit a wide range of systems.While 20 years ago these sorts of misconceptions about digital signals were understandable, today it should be common knowledge that digital interference is not the same as analog interference and behaves completely differently. They could easily update both to support full bandwidth, all formats but it's all about HDCP, which is a shame. Also, maybe Toshiba invented the original digital toslink connected but both are S/PDIF, which was created by Sony and Philips.(see below).

The consumer version of the TOSLINK standard has stayed stable for decades. A TOSLINK optical audio cable from the 1990s will work just like one you buy today. But don’t be tempted to try and use a standard RCA phono cable in place of a dedicated coaxial digital cable. They look similar and can work, but an analogue interconnect has different impedance values from a digital one (50 ohm versus 75 ohm), so won’t work as well. An entry-level cable like the QED Performance Coaxial will do a fine job for most. And, in our experience, compared to optical, a coaxial connection does tend to sound better. That's because it has greater bandwidth available, meaning it can support higher quality audio up to 24-bit/192kHz. Optical is usually restricted to 96kHz. The majority of TV and AV products launched over the last few years support HDMI version 2.0, but HDMI 2.1 (which supports 8K resolution content and features such as ALLM) is becoming more common among modern TVs and AV kit.TOSLINK is just the shortened trade name for Toshiba Link, both named for the company that introduced optical audio as a consumer standard. The answer to this will depend on the kit you’re using. If it’s a straight choice between coaxial and optical, we’d go for the former. In our experience, a coaxial connection tends to produce better audio quality than optical, allowing for a higher level of detail and greater dynamics. S/PDIF (Sony/Philips Digital Interface) is a type of digital audio interface used in consumer audio equipment to output audio over relatively short distances. The signal is transmitted over either a coaxial cable with RCA connectors or a fiber optic cable with TOSLINK connectors. Now I think the biggest advantage of coaxial over consumer optical is that coaxial is will work better over distances greater than ten feet, though I could be wrong about that. In addition to the long run as a tech writer and editor, Jason spent over a decade as a college instructor doing his best to teach a generation of English students that there's more to success than putting your pants on one leg at a time and writing five-paragraph essays. While his days of steering students toward greatness are behind him, his lifelong desire to delight, entertain, and inform lives on in his work at How-To Geek.

Pretty much this outside the fact that almost all HDMI cables shorter then 10 to 15ft max are copper. Really, you just need a well shielded cable although it's always a good idea to keep all cable runs as short as possible in my experience. In addition to our overview above, people often have specific questions about optical audio cables and connections. Here are some of the common ones. Are TOSLINK, Optical Audio, and Digital Audio All The Same?HDMI’s feature set, upgradability and the fact it can handle both audio and video means you don’t need to worry about too many wires clogging up your system. And, best of all, you won't sacrifice performance. Also, coaxial doesn't have the bandwidth required to support high-quality surround sound formats such as Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos and DTS:X. So, in a modern home cinema setting, its uses are quite limited. so assuming that the dac is equal in quality i would convert at the receiver. I could be mistaken, but my impression is that analog signals, especially unbalanced, low level signals, are susceptible to noise whereas digital signals, especially optical, are not. So you want to keep your analog signal path as short as possible. The main downside to a coaxial digital connection is the potential transfer of electrical noise between your kit. Noise is bad news when it comes to sound quality, but it exists in all AV components to one degree or another. Unfortunately, using a coaxial connection enables noise to travel along the cable from the source to your amplifier.