Joined in 2023 
82 
63 About this deal
If you are using slide-on hinges, first ensure the retaining screw on the mounting plate is loose enough to allow the hinge to slide on and then slide the hinge onto the plate until it slips into place. I didn’t make a template this time as I only had four hinges to do, but I will soon as I remembered there are two more small and shallow 9mm holes you need to drill to clear two ‘dimples’ on the hinge part going into the door. Once adjusted suitably to allow the door to open and close without touching or binding on any surrounding surfaces you’re pretty much done, good job!
Hinge Jigs of 2023 - Picks from Bob Vila The Best Door Hinge Jigs of 2023 - Picks from Bob Vila
another tip is to drill the hinge position into one of IKEA’s very own handle templates ( https://www. But, remembering that accuracy is key, a brand name template from a trusted woodworker brand like Porter Cable is a must. These jigs can be helpful to you when you planning to fit a couple of concealed (Euro-style) hinges for the inset cabinet doors. To test that your mark is accurate and in the correct place position the hinge so that the edge of the mounting plate is flush with line drawn in the above step. But I know that everything is wonky (technical term lol) on the corner cabinets, even the soft close mechanisms are special.However, only a few top brands make these compact saws and the features are similar to a portable table saw. Anyone who sells you blum hinges should not only be able to supply you with that information, but also has access to the various marking templates which Blum mfgrs. I bought the Kreg jig described by one of your readers but could not for the life of me figure out how to adapt it to our situation. If your using a hand held drill then I'd make a jig, drill a hole in a scrap of MDF and put a stop on it so that you can just hold the jig to the door and drill through the existing hole. Repeat the same for the bottom and also for any other hinges, again remembering to measure from the correct point.
Template for Ø35mm and 26mm Hinge LOOTICH Hole Drilling Jig Template for Ø35mm and 26mm Hinge
You might not know this, but the IKEA hinge system is contracted out to ‘Blum’, a leading hinge and furniture hardware supplier in the UK. If you are using clip-on hinges, gently wiggle the hinges down on to teh mounting plate until they clip in place. thanks for this post, after trying a dummy piece which I then made into a template, I cut the real door, it still needed some knocking and pushing.
These hinges are a fair bit smaller than the 35mm hinges so are commonly used on the smaller more light weight cupboards and units normally found in bathrooms. A high-quality router bit is included, as is a self-centering drill bit for making the actual hinge holes. Mark the inside of the two small holes, remove the hinge and drill 9mm holes around 4mm deep (little more than a dimple really). Although they’re both 35mm concealed hinges designs can vary so use an existing hinge to get an exact match Is the Cabinet Door Fitted Internally or Externally (Overlay or Inset)? The holes in the cabinet are usually 5mm diameter but this is only good for the little fat grub screws that IKEA use.
35mm Hinge Hole Saw Jig Drilling Guide Forstner Drill Set 35mm Hinge Hole Saw Jig Drilling Guide
This may be a dumb question, but can I use these measurements/template on Ikea products bought in the states? If you do need to make any position adjustments to you hinge see our project here that covers how to adjust concealed hinges and kitchen cupboard doors for full details.
I’m still looking for info to provide them so they can drill not only hinge placement on doors but the holes for the drawer fronts as well. If memory serves me right the backset for the front two screws is 1 3/8", but you can easily check this by doing a trial run eh? Without a template it is nearly impossible to get it straight and also have vertical position lined up perfectly.
Great Deal 
New Comment