Joined in 2023 
82 
63 About this deal
Top tip: If you suspect you may need a riser kit for the reasons mentioned above, make sure one is available for the tray you have selected (should you need it). If you are simply replacing an old shower tray with a new one it’s best to swap like for like e.g. same size and style with the waste in the same position, however if you want to fit a larger more elaborate tray try to match the waste positions closely. Baths All Baths Single Ended Baths Double Ended Baths Shower Baths Corner Baths Freestanding Baths Whirlpool Baths Roll Top Baths Slipper Baths Painted Baths
A Flush To Floor Shower Tray? - UK Bathroom Guru Can I Have A Flush To Floor Shower Tray? - UK Bathroom Guru
Tighten it so that it is “pinch” tight e.g. tighten it as much as you can by hand and then one final turn to pinch it up and seal it. You don’t need to over tighten it! The final task once the internal sealing is done is to then seal the gap at the front between the shower tray and the floor. It also takes longer to do and is more expensive, though steps can be taken sometimes to mitigate the risk (by reinforcing the floor in other ways when possible.) Basin Furniture Units Floor Standing Basin Units Wall Hung Basin Units White Bathroom Vanity Units Grey Bathroom Vanity Units Vanity Unit & Toilet Suites This drains our shallow shower tray perfectly in spite of the very powerful shower feeding it. Exactly what was needed.As we have mentioned installing a new shower tray with the waste in the same position as the old one should minimize potentially a great deal of work. Due to the damp damage to the walls we had to remove quite a few tiles, not only as they were loose, but also to replace the damaged sections of wall. Next, mark the floor area inside the tray waste so that you know exactly where you need to cut the hole for the waste.
Shower by Di Vapor - Cascade One Person 90cm x 90cm Steam Shower by Di Vapor - Cascade One Person
Taps By Brand hansgrohe Bathroom Taps Mira Bathroom Taps Grohe Bathroom Taps Vitusso Bathroom Taps Bristan Bathroom Taps Merano Bathroom Taps hansgrohe Kitchen Taps Rangemaster Kitchen Taps Bristan Kitchen Taps Sauber Kitchen Taps Reginox Kitchen Taps Insinkerator Boiling Water Taps If your shower tray is a long way from the external wall (where the waste pipe needs to go) and the waste pipe will have to be threaded through several joists due to their orientation, then it may be worth raising the tray up and running it above the floor.This will be easier to do, will maintain the structural integrity of your floor joists, and allow you easy access to the shower trap in the future should maintenance be required. When you have seen that everything is in the correct position, attach the waste to the shower tray and then connect this to the trap. By tiling down to the tray and leave a 2-3mm gap between the tiles and the tray you can fully seal this with silicone and allow for any expansion and contraction as the silicone itself will absorb this and reduce the risks of any leaks.A small channel was also cut at the front of the hole as the waste connection protruded out of the waste by a few inches.
Wirquin SLIM+ Extra Flat Shower Waste 90mm - Chrome Plated
Using silicone sealant, run a line along the edges of the tray, to ensure no water can get underneath, once the shower is in use. Now, using the shower tray’s waste hole as a template, mark the concrete where the waste is to be positioned. The first job is to remove the old tray if it’s still in place. Depending on how it’s fixed, this can be fairly straightforward or a bit of a nightmare. In this example we will be replacing an old 900×900 quadrant shower tray with a new 900×900 low level quadrant shower tray.
Note: We always recommend that a shower tray is installed before the walls are tiled as this allows for a much more water tight joint as you can then tile down to the tray and seal it correctly. How to install a low level or low profile shower tray
Great Deal 
New Comment