BELTBOX: Vocal Dampener for Singers, Actors, Performers, Stress Relief. A Portable Warm-Up Room! Gift for Singers!

Product Information

So you may need to tweak your biltong box setup carefully over time until you have a perfect balance. Biltong should dry to ‘semi-moist’ within 24-48 hours, and should not take longer than a week even if you like it crisp. Let’s now make sure no insects enter our biltong box. We’ll be adding pieces of mosquito net to the holes; we like to add them on the inside and outside of the box. So cut two round or square pieces per ventilation hole to size, and fire up that glue gun. Now you can add the glass door to the cabinet by sliding it into the hinges. Take your flat-head screwdriver to gently secure the glass door with the screws on the inside of the hinges. Once they are in place, you can position the left panel as intended, meaning at a 45-degree angle with the top panel, slide the left panel firmly into place by adding some pressure while holding the top panel in place. You can guide and attach the LED strips with the self-adhesive side around the corner profiles for both solutions.

Once all four profiles are sawed to size, we can add them by measuring 1.1 cm or 0.43 inches from the front of the panel to align the profiles. Many recipes call for vinegar in some sort. Sometimes for flavor, sometimes for purposes of preventing mold. I typically don’t use it, but many people associate the vinegar flavor with Biltong. As for the mold prevention: If you place clean meat in the box with a good low rpm fan, then you don’t need vinegar. Flavor So let’s measure first 2.5 cm or 1 inch from the top of the right panel; make sure to start measuring from the top of the hypotenuse as indicated on-screen. We’ll again measure two different points to align our tape measure. When you consider what you are really trying to do, which is create a practice space where you can get louder than normal, it's good for the price.

While it may seem annoying to do, leaving an apartment or shared living space to sing in your car is still a better option than singing into a pillow or not singing at all.

We have mounted the smaller hole saw of 3.8 cm or 1.5 inches to our drill, and we aligned it on the measured points, make sure not to drill through, as we’ll turn the panel and continue drilling from the other side.

An important step is adding the fan to the outside of our box. First, we will glue it in place by adding glue on the four corners of the fan. Once the glue is added, be swift with placing the fan over the big ventilation hole, as the glue tends to dry fast. Also, drill only halfway through the panel, as we’ll drill the remaining part from the other side. This is to have as least chipped paint as possible. It won't give you as much space as the BELTBOX can, but it's worth considering if you just want to let out a scream. Use A Portable Sound Booth It's a straightforward product with a strap if you want to sing or speak loudly while you have both hands free. There's no need to set anything up, and it comes with a carrying bag. It's also waterproof if you want to get loud in the shower or a pool area. The Price Point Is Affordable

We can easily do that by using simple washers. The only important thing is that the dowels can fit through the washer’s hole. We will glue a washer to each dowel hole which means we will use 8 washers. We will now drill the dowel holes on the indicated spots; while drilling, we‘ll make sure we don’t drill through the panel, so be careful you don’t add too much pressure on the drill. We now place the profile on the miter box and put the ‘X’ facing down; make sure to align the profile so it’s sawed in the right direction.

When the tape measure is nicely aligned on our two points, we place a mark every 7 cm or 2.76 inches. These are the four points that will be used to add the dowels to. But first, we’ll have to drill an extra hole to fit the power cable for the mains-powered strip. We’ll drill the hole on the same side as our fan to keep all wires together. Fun video: we also made a timelapse of biltong drying in our DIY IKEA box! 1. BUILDING NECESSITIES 1.1. Components