Joined in 2023 
82 
63 About this deal
Pactool: Trusted brand for decades – leaders in specialized construction, renovation and remodeling designs Cutting around windows and door frames is pretty straightforward. Use the tape measure to find out where the cut needs to be made, and use the framing square to accurately trace where the cuts need to be made on the corresponding piece of siding. Try to make these cuts as tight as possible. Although the painters will caulk the small gap between the end of the siding, and the corner trim, craftsmanship always wins and it will only help while striving for a water-tight finish. How to Install 4×8 Hardie Board Siding Make sure that the clamps are both set to the same level of reveal that you desire. Most of the time homeowners want a 7.25”-7.5” reveal, so play around and find what you like.
Siding Nails– These can vary, but the standard is a 2.5” siding nail. If you’re unsure of what nails you’ll need, ask someone in that department. I know marking studs can be tedious, but if done improperly you risk hitting water and electrical lines when nailing in the siding. Step 3 – Install Trim Other styles of fiber cement siding include shingles, vertical siding, 4×8 panels, trim, and soffit panels. How Much Does Fiber Cement Siding Cost? Start at the highest point you can, and pry the old siding off from the top down. Make sure to remove ALL nails. The last thing you want is to find out you missed a nail after setting a new hardie plank panel into place. Step 2 – Install House Wrap Hardie board is named after the James Hardie Brand, it’s arguably the most widely recognized brand of fiber cement siding. Other brands include:Siding – most suppliers carry Hardiplank, but ask if they carry another brand that may be cheaper. I personally used Nichiboard and it worked out to be a 30% savings as opposed to Hardie plank.
Installation: Make sure you buy a type of clamp that is easy to install on your particular type of siding. Adjustable clamps can often make installation easier by allowing you to adjust them to fit any size material without having to drill holes or make other modifications.A: The PacTool SA907 Adjustable Z-Clamp Panel Siding Installation Tool is machined from industrial grade components. Install all window and corner trim on the area you’ll be working on. Corner trim consists of installing one board flush with the corner of the house, and then overlapping it with another on the perpendicular corner. Don’t worry too much about seeing the seam in between the two boards, painter’s will caulk this later. Step 4 – Install First Row of Siding
You want a snug fit on the siding. The tightening lever should make no less than a 45 degree angle with the upper half of the siding. Overtightening can cause the gauge to pull away from the wall. Tha... A: Simply attach each Z clamp to the first course of flashing before placing the panel on the support plate – then nail as per manufacturer recommendations before continuing up the wall. Start by measuring the entire area you’d like to cover. Decide if it will be better to install the panels with the long side horizontal, or vertical. House Wrap – These come in large rolls measuring 9 feet long. You’ll need to shingle this after you tear off the old siding. (Shingling just means overlapping starting with applying the bottom first so that rain can’t run down into a lower layer) A: The patented friction cam mechanism allows this tool to fully support 16 foot lengths of LP Siding ensuring equal spacing between each board.
Fiber Cement siding is a combination of cement, water, sand, and cellulose fibers. The combination of these compounds provides a strong, long-lasting option for a home’s exterior. Another benefit of fiber cement is the ability to hold paint. Due to its porous nature, the material soaks up paint when applied. Tests have shown that paint also withstands fade from UV rays on fiber cement siding better than it would on other siding materials.
DIY Projects: Get rid of bulky spacer guides with these durable clamps; machined from industrial-grade components for years of use Depending on the model of gauge, we can handle 4”-8” reveals or 100mm-240mm on our metric model. There is also an extension kit available (SA90202.12) that works with our model SA902 which... If you have someone helping you, have them hold the starting board while you ensure its level. Once you find the perfect spot, start nailing it to the house at the studs. Hit every stud you can.Work from bottom to top, so that the boards on rows 2 and above will have row 1 to rest on while you shimmy them into place. Siding Tools: Works for all fiber cement panel siding and flashing sizes with large, easily adjustable plates while creating consistent, accurate siding to flashing gaps Like any substantial project, you’re going to have times when you’re tired, you’ve been working all day, and looking at the area left to do is daunting. That’s Okay! After flipping my first house, this was probably one of the most important lessons I’ve learned.
Great Deal 
New Comment